LUKAS LK-7900 Ara Dash Cam Driver
LUKAS LK ARA is an upgrade to ACE; it features OBD-II module that connects with your car. Read complete review to know Support: GB. LK ACE's Upgraded Version, Support OBD II, Forget about the other footages, Here new concept dash cam comes! LK ARA works in C to 80C. Free Download LUKAS LK Ara Dash Cam Firmware (Digital Camera / Webcam / Camcorder).
|Supported systems:||Windows All|
|Price:||Free* [*Free Regsitration Required]|
LUKAS LK-7900 Ara Dash Cam Driver
He also said that the operation was nearly automated.
This camera can detect and register collisions, storing information about them like where they occurred, at what speed, and from exactly which direction. This model uses the latest SD cards, supporting up to GB of video storage space.
Lukas LK 7900 ARA Review
This DVR is set by default to record over the oldest clips if you do run out of space, but the options can be changed using the included software. It starts when the car does, runs off of the vehicle battery, and works continuously according to all of the settings.
This camera system records in full-color p, with resolution that can be lowered for anyone who needs ultra-long recording times. It has a button that turns on the in-car microphone, as well as an emergency button that stores 20 seconds of video with sound in a separate file. The LUKAS LK-7900 Ara Dash Cam mode works in a helpful way, saving the 10 seconds before you push the button as well as the next 10 seconds.
ALSO before you start to disassemble, check the camera works with your bench 12v supply and VGA connected to a monitor.
Lets start with a known working item! Remove SD card and all cabling.
Put camera on work bench lens uppermost. At six oclock bottom find small 2mm notch in rim. Insert a small thin flat blade into the slot and carefully start to lift the LUKAS LK-7900 Ara Dash Cam upwards. Great care should be taken not to crease the thin plate.
LUKAS LK ARA [Review] – What’s Good & Bad?
Gradually work your way around the whole ring until it comes free. Lift it away and store.
The reverse side is tacky with impact adhesive. You will now see two holes at the bottom of the cam, previously covered by the plate. With a small x-point screwdriver remove the two screws.
Lukas LK-7900 Ace
With the cam lens upwards, lift the front plastic housing containing the lens turret away from the rear housing. Do this gently and keep the lift straight. The only thing holding the two halves together are the plugs and sockets on the pcbs. When you split the housing, either the lens pcb LUKAS LK-7900 Ara Dash Cam the larger circular pcb will come away from the rear pcb which is screwed in.
The lens holder and ccd pcb LUKAS LK-7900 Ara Dash Cam screwed to the inside of the lens turret. Carefully remove the square of glass tape that is stuck onto the lens holder and heat sink…. You WILL need to use this again so remove it very carefully!
Lukas LK ARA Dashboard Camera Gps Ready Review
Put a mark on the heatsink and edge of pcb so as to know orientation when reassembling cam. Unscrew the two x-point screws and very carefully lift the lens holder up and away from the heat sink.
There is NO need to remove the heat sink from the front housing. With a fine pointed needle remove the glue between the lens holder and lens holder body, and free the holder so it can screw in and out freely.
Wrap the lens holder in insulation tape and use a very small pipe wrench to break the stiction of the glue. The HD cmos sensor is inside the assembly.
LUKAS Lk FHD Ara GPS Car Dashboard Camera Blackbox 8gb eBay
It is keeping the CMOS sensor from being ruined by dust and foreign matter falling onto it. When the lens holder is rotates freelythen reassemble enough of the camera to test it. Gently press the loose circular pcb onto the fixed pcb, that is screwed to the rear housingmaking sure the two mating halves LUKAS LK-7900 Ara Dash Cam the inter pcb connector engage. Be careful if you tilt the cam forward, the pcbs will fall off.
- What Do The Customers Say?
Secure the pcbs with a strapping of insulation tape for safety. Connect the VGA cable and the 12v supply. Insert your sd card into the camera.
Do this gently otherwise you will push the pcbs off each other. Now the acid test!